WARNING: As blade starts cutting the material, release the lower guard immediately. screw. Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool. Questions & Answers Page A. Investigate and take corrective action to eliminate the cause of blade binding. Also, never pull the. The torque from the motor can cause the tool to twist. Damaged cords increase the risk of electric shock. Do not use “AC only” rated tools with a DC power supply. have the saw plugged into a power source. (See Switch & General Cuts on page 10.). Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. Such preventive safety measures reduce the risk of starting the tool accidentally. If damaged, have the tool serviced before using. Be sure the large diameter of the OUTER washer lays flush against the blade. Apply a light forward pressure. 2 Field. 11). Holding the work by hand or against your body is unstable and may lead to loss of control. Use the right side of the foot against the board guide. Use safety equipment. the depth adjustment lever located between, the guard and handle of saw. Do not support the work with the narrow sides as this is an unsteady arrangement. When the foot rests flat on the surface being cut, proceed cutting in forward direction to end of cut. When cutting is interrupted, to resume cutting: squeeze the trigger and allow the blade to reach full speed, re-enter the cut slowly and resume cutting. This symbol designates that this tool is listed by Underwriters Laboratories, and listed to Canadian Standards by Underwriters Laboratories. Accessories that may be suitable for one tool, may become hazardous when used on another tool. It also increases the surface area of the blade available for pinching under conditions of kerf close down. The correct tool will do the job better and safer at the rate for which it is designed. SM 2610921914 2-04 2/25/04 10:04 AM Page 7, Functional Description and Specifications, Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Set foot to maximum depth of cut setting. For example: internal wires may be misplaced or pinched, safety guard return springs may be improperly mounted. Size of drill bits, grinding wheels, etc. Distractions can cause you to lose control. Skil 5750 TYPE 1 circular saw parts - manufacturer-approved parts for a proper fit every time! For example: internal wires may be misplaced or pinched, safety guard return springs may be improperly mounted. The laser light guide is a class IIIA laser with a maximum output power of 5.0 mWatts and conforms to 21 CFR 1040.10 and 1040.11. Raise the lower guard, using lift lever and hold the saw by the front and rear handles (Fig. We have emailed you a verification link to. ! Avoid cutting nails. Keep handles dry, clean and free from oil and grease. Last Name. Turn saw around and finish the cut in the normal manner, sawing forward. SM 2610921914 2-04 2/25/04 10:04 AM Page 9, Disconnect plug from power source. See “Cutting Large Sheets” in this manual. Ships in 10 - 16 business days. Required * First Name. Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Raise lower guard by Lower Guard Lift Lever. Replace damaged cords immediately. Circular saws are not designed or intended to be used as table saws. There is an increased risk of electric shock if your body is grounded. Do not continue to turn the adjustment screw after the line stops moving or if it becomes significantly harder to turn the. CLUTCH, because the proper setting of the CLUTCH, combined with firm handling of the saw will allow you to control KICKBACK. similar reflective surfaces are not recommended for laser use. takes for the blade to come to a complete stop during coast down. Do not use tool while tired or under the influence of drugs, alcohol, or medication. Wet lumber, green lumber or pressure treated lumber require special attention during cutting operation to prevent KICKBACK. When starting the tool, hold it with both hands. If the plug does not fit fully in the outlet, reverse the plug. 13). To turn tool “ON”, press the release button with your thumb on either side of handle to disengage the lock, then squeeze the trigger switch. Accidental start-up of the saw may cause injury. Continue to depress button, turn wrench. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. ! Do not use wrenches with longer handles, since it may lead to over tightening of the blade stud. 14). activities contains chemicals known to cause cancer, birth defects or other reproductive harm. WARNING: Allow blade to come to a complete stop before lifting the saw from cut. $8.80 Add to Cart. Do not wear loose clothing or jewelry. This plug will fit in a polarized outlet only one way. Don't expose power tools to rain or wet conditions. Support the panel or board close to the cut, as shown in (Fig. When cutting across the grain, the fibers of the wood have a tendency to tear and lift. below, may result in electric shock, fire and/or serious personal injury. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. 2.Retract the lower guard all the way up into the upper guard. "), SM 2610921914 2-04 2/25/04 10:04 AM Page 1, Instrucciones de funcionamiento y seguridad, 1-877-SKIL999 (1-877-754-5999) http://www.skil.com, SM 2610921914 2-04 2/25/04 10:04 AM Page 2, Read and understand all instructions. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. Electrician’s rubber gloves and footwear will further enhance your personal safety. Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator. Lower guard should be retracted manually only for special cuts such as “Pocket Cuts” and “Compound Cuts”. Use only accessories that are recommended by the manufacturer for your model. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. 5. A moment of inattention while operating power tools may result in serious personal injury. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. DIRECT EYE EXPOSURE. Welcome to ManualMachine. motor housing. Inspect for and remove all nails from lumber before cutting. If saw blade is binding, it may walk up, SM 2610921914 2-04 2/25/04 10:04 AM Page 5. or KICKBACK from the workpiece as the saw is restarted. This tool is not recommended for continuous and general usage with metal or masonry cut-. Some dust created by power sanding, sawing, grinding, drilling, and other construction. The new SKIL 3376 4 x 36-inch Belt/Disc Sander is a two-in-one sanding station. Proper footing and balance enables better control of the tool in unexpected situations. Contain long hair. . 3). Wet Diamond Wheels. The correct tool will do the job better and safer at the rate for which it is designed. Press the lock button and turn wrench until lock button engages. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw blade, but not in line with the saw blade.